Digiplex DGP-641 Manual de instalación Pagina 56
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
52 Reference & Installation Manual
3.4 Display Entry Delay Timer
SECTION [003]: OPTION [3]
The Entry Delay Timer will be programmed to provide the user time
to enter their User Access Code before the alarm is triggered. The
Entry Delay Timer's countdown can be displayed on the LCD
screen.
Option [3] OFF= Will not display the Entry Delay Timer (default)
Option [3] ON = LCD screen will display Entry Delay Timer
3.5 Confidential Mode
SECTION [003]: OPTIONS [4] AND [5]
If Confidential Mode is enabled and no actions are performed on
the keypad for a period of time, the LCD will appear as shown in
Figure 30 (page 52) and the “AC” and “STATUS” LED will be OFF.
The period of time in which no action is performed is defined by the
Confidential Mode Timer (005-255 seconds; refer to section
section 3.6 on page 52). Confidential Mode is activated by enabling
option [4]. Option [5] regulates whether the LCD screen will be
activated at the touch of a button or only when an access code is
entered.
Once the LCD screen is activated (by code or button), Normal
Mode will appear and display the date and time as shown in Figure
30 on page 52. The status of the areas, the open zones for every
area the keypad is assigned, the Alarm Memory Display (if
necessary) and the Trouble Display (if necessary. See DGP-848
User Manual) will also scroll on the LCD screen. By default, options
[4] and [5] are OFF.
Section [003]:
Option [4] OFF= Normal Mode
Option [4] ON = Confidential Mode
Option [5] OFF= LCD screen activated by entering an access code
Option [5] ON = LCD screen activated by pressing a button
Figure 30 : LCD Screen
3.6 Confidential Mode Timer
SECTION [007]
Section [007] determines the amount of time without action before
the keypad enters Confidential Mode. For more information on
Confidential Mode, refer to Confidential Mode on page 52.. The
Confidential Mode Timer can be set from 005 seconds to 255
seconds. Default: 120 secs.
3.7 Time Display Option
SECTION [003]: OPTION [8]
The LCD keypad comes with a time display option that can display
the date as year/month/day or as day/month/year.
Option [8] OFF= Date displayed as yy/mm/dd (default)
Option [8] ON = Date displayed as dd/mm/yy
3.8 Muting
SECTION [004]: OPTION [1]
The keypad can be programmed not to emit audible sounds,
including Chimed zones. During Muting, the keypad will only emit
the Confirmation Beep, Rejection Beep, and beep when a button is
pressed.
Option [1] OFF= Audible sounds (default)
Option [1] ON = Mute
3.9 Beep on Exit Delay
SECTION [004]: OPTION [2]
The keypad can beep once every second during the Exit Delay
Timer. During the final 10 seconds, it will beep more rapidly to
provide a final warning before the area is armed.
Option [2] OFF= Exit Delay beep disabled
Option [2] ON = Exit Delay beep enabled (default)
3.10 Chime on Zone Closure
SECTION [004]: OPTION [4]
During the Chime Zone Time Period that the user sets, the keypad
can emit an intermittent beep whenever a zone with the Chime
feature enabled closes (see DGP-848 User Manual for details on
Chime Zones). If the user does not set the Chime Zone Time
Period and this option is enabled, the Chime Zones will always
beep upon closure.
Option [4] OFF= Chime on Zone Closure disabled (default)
Option [4] ON = Chime on Zone Closure enabled
3.11 Beep on Trouble
SECTION [005]: OPTIONS [1] TO [4]
Potential troubles have been sorted into groups. With these options
enabled, the keypad will emit an intermittent beep tone whenever a
trouble condition from the Trouble Groups occurs in the system.
The intermittent beep will remain activated until the user enters the
Trouble Display or if the trouble is resolved. For a list of the
troubles, see the DGP-848 Reference and Installation Manual. The
intermittent beep will be re-initialized whenever the trouble
condition re-occurs.
O
ption [1] OFF = Beep disabled: System Troubles and Clock Loss
Option [1] ON = Beep enabled: System Troubles and Clock Loss
Option [2] OFF= Beep disabled: Communicator Troubles
Option [2] ON = Beep enabled: Communicator Troubles
Option [3] OFF= Beep disabled: Module and Combus Troubles
Option [3] ON = Beep enabled: Module and Combus Troubles
Option [4] OFF= Beep disabled: all Zone Troubles
Option [4] ON = Beep enabled: all Zone Troubles
3.12 Keypad Tamper Enable
SECTION [006]: OPTION [5]
With tamper enabled and the on-board tamper switch is triggered,
a Tamper report will be sent to the control panel via the combus.
Option [5] OFF= Keypad's tamper is disabled (default)
Option [5] ON = Keypad's tamper is enabled
3.13 Time Format
SECTION [005]: OPTION [7]
This feature determines whether the time shown on the screen will
be displayed using the International time format (24Hr. clock) or the
US time format (AM/PM).
Option [7] OFF= Time uses the International time format (default).
Option [7] ON = Time uses the US time format.
3.14 Combus Voltmeter
The combus voltmeter displays the real-time voltage and verifies if
the combus is supplying sufficient power at the keypad module’s
location. Readings will appear on the LCD screen. A reading of
10.5V indicates that the voltage is too low. This may occur when
too many modules are connected to the combus, a module is
installed too far from the panel or if the system is running on the
- Table of Contents 3
- Introduction 5
- Installation 6
- DGP-848 Control Panel 3 7
- BELL output has 8
- AUX. OUTPUT = 700mA 9
- 2.9 Programmable Outputs 10
- 2.10 Combus Connections 10
- 2.11 Single Zone Connections 10
- 2.12 Double Zone Connections 11
- 2.13 Keypad Zone Connections 11
- 2.14 Keyswitch Connections 11
- 2.15 Fire Circuits 11
- ENTER] (LCD keypads) or [ 12
- Programming Methods 13
- 3.6 Level Programming 14
- 3.7 Paradox Memory Key 14
- Zone Programming 15
- 4.1 Zone Numbering 16
- 4.2 Zone Definitions 16
- 4.3 Zone Partition Assignment 17
- 4.4 Zone Options 17
- 4.5 Zone Labels 18
- DGP-848 Control Panel 15 19
- 4.6 Input Speed 20
- 4.7 EOL Zones 20
- 4.8 Zone Doubling (ATZ) 20
- Keyswitch Programming 21
- 5.2 Keyswitch Definitions 22
- 5.4 Keyswitch Options 22
- 6.1 Arming Follows Partition 23
- 6.3 No Arming On Tamper 23
- 6.5 Timed Auto-Arming 23
- 6.6 No Movement Auto-Arming 24
- 6.7 Auto-Arming Options 24
- 6.8 One-Touch Features 24
- 6.9 Exit Delay 24
- 6.10 Keypad Lock-out Feature 24
- ECTIONS [238] TO [241] 25
- ECTION [504]: OPTION [5] 25
- Alarm Options 26
- 7.5 Keypad Panic Options 27
- Event Reporting 28
- 8.1 Reporting Enabled 29
- 8.2 Report Codes 29
- 8.4 Partition Account # 31
- 8.5 Reporting Formats 31
- 8.6 Event Call Direction 31
- Dialer Options 33
- Programmable Outputs 34
- 10.2 PGM Deactivation Event 35
- 10.3 PGM Deactivation Option 35
- 10.4 PGM1 Is Smoke Input 35
- PGM Programming Table 36
- DGP-848 Control Panel 33 37
- (when system is 38
- (Tamper/Fire Loop) 38
- (Low Battery 38
- Supervision) 38
- 12.1 Hardware Reset 39
- 12.2 Software Reset 39
- 12.3 Battery Charge Current 39
- DGP-848 Control Panel 37 41
- Access Codes 42
- 13.5 User Options 43
- 13.7 Access Control 43
- 13.8 Multiple Action Feature 44
- Access Control 45
- 14.6 Access Levels 46
- 14.7 Schedules 46
- 14.8 Holiday Programming 46
- DGP-848 Control Panel 43 47
- WinLoad Software 48
- User Features 49
- 16.2 Bypass Programming 50
- 16.3 Chime Zones 50
- 16.4 Access Codes 50
- 16.6 Keypad Settings 51
- 16.7 Trouble Display 51
- 16.8 Trouble Latch 52
- 16.9 Clear Bell Limit Trouble 52
- 16.10 Event Record Display 53
- 1.0 INSTALLATION 54
- 2.0 PROGRAMMING 55
- 3.0 SYSTEM OPTIONS 55
- 641BL ONLY) 57
- 6.0 MESSAGE PROGRAMMING 59
- Table 14: Message Programming 59
- 7.0 PROGRAMMING SECTIONS 60
- DGP-848 Control Panel 57 61
- DGP-848 Control Panel 59 63
- Warnings 64
- FCC Warnings 64
- CTR-21 Warnings 64
- General Warning 64
- UL and C-UL Warnings 64
- Warranty 65
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641
(60 paginas)Husqvarna 355 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Narzędzie do benzyny Husqvarna 355.
Dostarczamy 1 pdf podręczników Husqvarna 355 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales