Digiplex DGP-641 Manual de instalación descargar pdf (Pagina 49)

DGP-848 Control Panel 45

15.9 Call Back Feature

SECTION [522]: OPTION [1]

For additional security, when a computer using WinLoad attempts

to communicate with the control panel, the control panel can hang

up and call the computer back to re-verify identification codes and

re-establish communication. When the control panel hangs up,

WinLoad automatically goes into Wait For Call Mode, ready to

answer when the control panel calls back. Please note that the PC

Telephone Number must be programmed in order to use the Call

Back feature.

16 User Features

16.1 Arming and Disarming Features

Partitions can be armed using various arming methods. Refer to

section 16.1.7 for information on how to arm.

16.1.1 Regular Arming

This method is used for the everyday arming of the system. All

zones within the partition must be closed to arm the system. The

system can also be Regular armed by using a One-Touch Feature

(see section 6.8 on page 20) or a keyswitch (see section 5.4.6 on

page 19). All users are able to Regular arm the partition(s)

assigned to their user access codes.

16.1.2 Stay Arming

Stay arming will partially arm the partition to permit the user to

remain in the protected area. The programmed Stay Zones (see

section 4.4.3 on page 14) will not arm when Stay arming a partition.

For example, the doors and windows can be armed without arming

the motion detectors. The system can also be Stay armed by using

a One-Touch Feature (see section 6.8 on page 20) or a keyswitch

(see section 5.4.3 on page 18). Only user access codes with the

Stay and Instant Arm option enabled can Stay arm a partition.

16.1.3 Stay Arming with Delay

Stay arming with Delay functions like Stay arming except armed

zones can be programmed with an Entry Delay Timer (see section

4.2.9 on page 13). If these zones are accidently triggered, the timer

will start to allow the user time to disarm the partition(s).

16.1.4 Instant Arming

This feature is similar to Stay arming. Instant arming will partially

arm the partition to permit the user to remain in the protected area,

but all zones, including the entry/exit point, are changed to instant

alarm zones. Therefore, if any armed zone is breached, the alarm

will instantly be triggered. The system can also be Instant armed by

using a One-Touch Feature (see section 6.8 on page 20) or a

keyswitch (see section 5.4.5 on page 19). Only user access codes

with the Stay and Instant Arm option enabled can Instant arm a

partition.

16.1.5 Instant Arming with Delay

Instant arming with Delay functions like Instant arming except

armed zones can be programmed with an Entry Delay Timer (see

section 4.2.9 on page 13). If these zones are accidently triggered,

the timer will start to allow the user enough time to disarm the

partition(s).

16.1.6 Force Arming

Force arming allows the user to arm a partition when Force zones

are open (see section 4.4.4 on page 14). Once the open zone in an

armed partition is closed, however, the system will then arm it as

well. This feature is commonly used when a motion detector is

protecting an area that is occupied by a keypad. For example,

during Force arming the motion detector will remain unarmed until

the user exits the area that it protects. The system will then arm the

motion detector. The system can also be Force armed by using a

One-Touch Feature (see section 6.8 on page 20) or a keyswitch

(see section 5.4.4 on page 18). Only user access codes with the

Force Arm option enabled can Force arm a partition.

16.1.7 How to Arm

The following section details how to arm the system using an LCD

or Grafica keypad.

For LCD keypads:

To arm, users:

1) Enter their [

ACCESS CODE].

2) Press the key corresponding to the desired arming method

(see Table 13). If the users have access to more than one

partition, they can press the key corresponding to the desired

partition or press [0] to arm all their assigned partitions.

For Grafica keypads:

To arm, users:

1) Enter their [

ACCESS CODE].

2) Using the scroll keys, highlight the desired arming method

(see Table 13) and then press the center action key (Ok). If

you have access to more than one area, proceed to step 3.

3) Highlight either Arm All Areas or Select Area(s) and then

press the center action key (Ok). If you selected the Select

Area(s) method, follow steps 4 and 5.

4) Highlight an area you wish to arm and then press the left

action key (Select). Repeat this step for any additional area.

5) Press the center action key (Arm)

Table 13: .Arming Methods

16.1.8 Disarming

Users can only disarm the partitions assigned to their user access

codes. User access codes with the Arm Only option (see section

13.5.4 on page 39) enabled cannot disarm.

For LCD keypads:

To disarm, users:

1) Enter through a designated entry. The Entry Delay Timer will

begin.

2) Enter their [

ACCESS CODE].

Arming Method LCD Grafica

Regular [

ARM]

(Arm System)

Stay [

STAY]

(Stay Arm)

Instant [5]

(Instant Arm)

Force [FORCE]

(Force Arm)

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex DGP-641 Manual de instalación Pagina 49

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641