Digiplex DGP-641 Manual de instalación descargar pdf (Pagina 50)

46 Reference & Installation Manual

3) Press the [

DISARM] key. If the users have access to more than

one partition, they can press the key corresponding to the

desired partition or press [0] to disarm all their assigned

partitions.

For Grafica keypads:

To disarm, users:

1) Enter through a designated entry. The Entry Delay Timer will

begin.

2) Enter their [

ACCESS CODE].

3) Using the scroll keys, highlight Disarm and then press the

center action key (Ok). If you have access to more than one

area, proceed to step 4.

4) Highlight either Disarm All Areas or Select Area(s) and then

press the center action key (Ok). If you selected the Select

Area(s) method, follow steps 5 and 6.

5) Highlight the area you wish to disarm and then press the left

action key (Select). Repeat this step for any additional area.

6) Press the center action key (Disarm).

16.2 Bypass Programming

Bypass Programming allows users to program the alarm system to

ignore specified zones the next time the system is armed. For a

user to bypass a zone, the zone must have the Bypass option

enabled, the user access code must have the Bypass option

enabled, and the zone must be within the user access code’s

partition assignment.

For LCD keypads:

To bypass, users:

1) Enter their [

ACCESS CODE].

2) Press the [BYP] key.

3) Enter the zones’ 2-digit number.

4) Press [

ENTER] key to exit.

For Grafica keypads:

To bypass, users:

1) Enter their [ACCESS CODE].

2) Using the scroll keys, highlight Bypass and then press the

center action key (Ok).

3) Highlight the zone that you wish to bypass and then press the

left action key (Bypass). Repeat this step for any additional

zone.

4) Press the right action key (Back) to save the data.

Users can also activate Bypass Recall. Bypass Recall reinstates all

the zones that were bypassed the last time the partition(s)

assigned to the user access code were armed.

For LCD keypads:

To activate Bypass Recall, users:

1) Enter their [

ACCESS CODE].

2) Press the [

BYP] key.

3) Press the [

MEM] key.

4) Press [

ENTER] key to exit.

For Grafica keypads:

To activate Bypass Recall, users:

1) Enter their [

ACCESS CODE].

2) Using the scroll keys, highlight Bypass and then press the

center action key (Ok).

3) Highlight Bypass Recall and then press the center action key

(Ok).

16.3 Chime Zones

The keypads can be programmed to emit rapid, intermittent beeps

whenever designated zones within their assigned partitions are

opened or when they are opened within a certain time period.

These zones are Chime Zones. The instructions that follow are for

LCD keypads. For Grafica keypads, a complete Grafica user

manual is available on our website at www.paradox.ca.

For LCD keypads:

To program a Chime Zone, users:

1) Enter their [

ACCESS CODE].

2) Press the [9] key.

3) Press the [1] key.

4) Enter the zones’ 2-digit number.

5) Press [

ENTER] key to save.

To program a time period when the Chime Zones are activated,

users:

1) Enter their [

ACCESS CODE].

2) Press the [9] key.

3) Press the [2] key.

4) Enter the time that keypads will start beeping when Chime

Zones are opened according to the 24-hour clock (i.e. 9AM is

09:00 and 9PM is 21:00).

5) Enter the time that keypads will stop beeping when Chime

Zones are opened according to the 24-hour clock (i.e. 9AM is

09:00 and 9PM is 21:00).

6) Press [

ENTER] key to save.

16.4 Access Codes

Refer users to the appropriate manual: LCD Keypad System

Manager’s Manual or LED Keypad User Manual.

16.5 Normal and Confidential Modes

For LCD Keypads:

When no actions are being performed on the keypad, the keypad

will remain in Normal Mode as shown in Figure 23 and will

automatically display:

• The current status of the zones for every area the keypad is

assigned

• The Alarm Memory Display if any alarms have occurred

• The Trouble Display if any troubles are occurring

• The current state of the Indicator Lights

In Confidential Mode:

• The zones and status messages will NOT be displayed

• The Indicator Lights will not illuminate

Depending on how the keypad was programmed, the user must

press a key or enter a user access code to illuminate the Indicator

Lights and activate Normal Mode.

1 2 ... 45 46 47 48 49 50 51 52 53 54 55 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex DGP-641 Manual de instalación Pagina 50

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641