Digiplex DGP-641 Manual de instalación descargar pdf (Pagina 47)

DGP-848 Control Panel 43

14.10 Global Access Door Features

14.10.1 Burglar Alarm On Forced Door

SECTION [537]: OPTION [5]

An Access Door can be assigned to a zone in the Digiplex security

system to also be protected by the burglar alarm. If an armed

Access Door is forced open (see section 14.2 on page 41), it can

send a signal to the control panel to trigger a burglar alarm and to

report to the Monitoring Station. The burglar alarm is generated

instantly regardless of the zone’s definition (i.e. entry delay is

ignored).

For this feature to function, the following must be done:

• Install a door contact (see appropriate Digiplex Module

Reference & Installation Manual)

• Assign the Access Door to a zone (see section 4 on page 11)

• Enable option [4] in section [537]: Log Door Forced Open

Restore (optional) (see section 14.9 on page 42)

• Enable option [5] in section [537]: Burglar Alarm on Forced

Door (see section 14.10.1)

Option [5] ON = Burglar Alarm on Forced Door enabled

Option [5] OFF = Burglar Alarm on Forced Door disabled (default)

14.10.2 Skip Exit Delay When Arming With Access Card

SECTION [537]: OPTION [6]

When an Access Card is presented to a reader twice within

approximately 5 seconds with the door closed, some or all the

partitions (see section 14.5 on page 41) assigned to the Access

Door can arm with or without starting the Exit Delay. This feature is

useful when the reader is outside the partition so the partition will

be armed immediately.

Option [6] ON = The Exit Delay will not be triggered

Option [6] OFF = The Exit Delay will be triggered (default)

14.10.3 Burglar Alarm On Door Left Open

SECTION [537]: OPTION [7]

An Access Door can be assigned to a zone in the Digiplex security

system to also be protected by the burglar alarm. Each Access

Door is programmed with a period of time that it is allowed to

remain open. Once the door has been open longer than the

programmed time period, a signal can be sent to the control panel

to trigger the burglar alarm and to report to the Monitoring Station.

For this feature to function, the following must be done:

• Install a door contact (see appropriate Digiplex Module

Reference & Installation Manual)

• Assign the Access Door to a zone (see section 4 on page 11)

• Enable option [3] in section [537]: Log Door Left Open Restore

In Event Buffer (optional) (see section 14.9 on page 42)

• Enable option [7] in section [537]: Burglar Alarm on Door Left

Open (see section 14.10.3)

Option [7] ON = Burglar Alarm on Door Left Open enabled

Option [7] OFF = Burglar Alarm on Door Left Open disabled

(default)

14.10.4 Door Access During Clock Loss

SECTION [537]: OPTION [8]

If the system registers a Clock Loss Trouble, the system will no

longer be able to recognize the Schedules. Only the System

Master Code and user access codes with the Master feature

enabled can reset the clock when option [8] is enabled. To avoid a

Clock Loss Trouble, the Digiplex Time Module (DGP2-TM1) can be

installed on the control panel. Until the Clock is reset, the Access

Control system can be programmed to grant access to:

Option [8] ON = the System Master Code, User Access Codes

with the Master feature or Schedule 00 (00=all

times) enabled

Option [8] OFF = all users regardless of their programmed

Schedule (default)

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex DGP-641 Manual de instalación Pagina 47

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641