Digiplex DGP-641 Manual de instalación descargar pdf (Pagina 41)

DGP-848 Control Panel 37

on the module will begin to flash until the serial number is re-

entered into section [952] or the appropriate tamper or unlocate

switch on the module is pressed.

12.11 Module Programming

SECTION [953]

All modules connected to the combus are programmed through the

control panel. Therefore, if you wish to program a module, enter

section [953] to enter Module Programming Mode (see section 3.2

on page 9) and key in the module's serial number. At this point, any

sections entered will be those of the selected module. For details

on how to program the modules, refer to the module's Installer’s

Guide or the module’s Programming Guide. To exit this mode,

press the [

CLEAR] key on LCD keypads, or the right action key

(Exit) on Grafica keypads, as many times as needed to return to

the desired screen.

12.12 Module Broadcast

SECTION [954]

This feature allows you to copy the contents of all programming

sections from one module to one or more of the same type of

module.

The Module Broadcast feature will only work when a

module is broadcasting its data to a module or to

modules of the same type and model number. For

example, an APR-PRT1 (Printer Module) cannot

broadcast to an APR3-PRT1. Likewise, a DGP module

cannot broadcast to a DGP2 module.

1) Press and hold the [0] key.

2) Enter the [

INSTALLER CODE] (Default is 000000).

3) Enter [954].

4) Enter the source module’s 8-digit [

SERIAL NUMBER].

5) Enter the destination module’s 8-digit [SERIAL NUMBER].

Repeat this step once for every additional module.

6) For LCD keypads, press [

ACC]. For Grafica keypads, press the

center action key (Start).

For example: Using an LCD keypad, you've completed the

programming of a zone expansion module (sn#34540033) and you

wish to program another two zone expansion modules

(sn#34540075 and sn#34412100) with the same settings:

1) Press and hold the [0] key.

2) Enter the [

INSTALLER CODE].

3) Enter [954].

4) Enter 34540033, 34540075, and 34412100.

5) Press [

ACC].

The control panel will automatically copy the contents of 34540033

into the other two zone expansion modules.

12.13 Remove Module

SECTION [955]

After entering section [955], the control panel will scan all modules

connected to the combus. If any missing modules are detected (i.e.

detector removed from the combus) during this scan, the control

panel will erase the module's serial number and remove the

module from the control panel's memory.

12.14 Serial Number Viewing

SECTION [900]

This feature allows you to view the serial number of the control

panel as well as the serial numbers of all modules connected to the

combus.

For LCD keypads: After entering section [900], the keypad will

display the 8-digit serial number of the control panel. Use the [

and [

T] keys to scroll through the serial number of each module

connected to the combus.

For Grafica keypads: After entering section [900], the keypad will

display the 8-digit serial number of the control panel. Press the

center action key (Next) to scroll through the serial number of each

module connected to the combus.

12.15 Power Save Mode

SECTION [504]: OPTIONS [4]

When the control panel is running on the backup battery (no AC),

the control panel can set all keypads into a “sleep mode” or Power

Save Mode. In Power Save Mode the keypad's backlight and LEDs

will be disabled until a key is pressed, an alarm occurs or an Entry

Delay is triggered.

12.16 Auto Trouble Shutdown

SECTION [218]

If, in a 24-hour period, a trouble has occurred more than the

number of times programmed in section [218], the control panel

will no longer report this trouble. Enter a value (001 to 015, 000 =

disabled) into section [218]. Please note that each trouble has its

own counter. This counter is reset every day at midnight or when a

Module Scan is performed (see section 12.6 on page 36). Also,

note that it cannot be set to more than 15.

12.17 No AC Fail Display

SECTION [503]: OPTION [7]

With option [7] in section [503] enabled, the control panel will not

display the AC Failure as a trouble. This means that when an AC

Failure occurs when this option is on:

• the AC LED will extinguish

• the trouble will not appear in the Trouble Display

• the keypad will not beep to indicate the trouble

• the AC Failure report code will be reported.

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex DGP-641 Manual de instalación Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641