Digiplex DGP-641 Manual de instalación descargar pdf (Pagina 27)

DGP-848 Control Panel 23

Regardless of whether the partition is armed or disarmed

when a tamper or wire fault occurs, the Zone Fault trouble will

appear in the keypad's Trouble Display and the control panel will

transmit the appropriate report code (see section 8.2 on page 25).

Follow Zone’s Alarm Type

[5] OFF and [6] ON

If a partition is armed, the control panel will generate a standard

alarm when a tamper or wire fault occurs. If the partition is

disarmed when a tamper or wire fault occurs, the Zone Fault

trouble will appear in the keypad's Trouble Display and the control

panel will transmit the appropriate report code (see section 8.2 on

page 25).

Audible Alarm

[5] ON and [6] ON

If a partition is armed, the control panel will generate a standard

alarm when a tamper or wire fault occurs. If the partition is

disarmed when a tamper or wiring failure occurs, the appropriate

trouble will appear in the keypad's Trouble Display, the control

panel will transmit the appropriate report code (see section 8.2 on

page 25), and it will generate an audible alarm.

7.4.1 Tamper Bypass Options

SECTION [501]: OPTION [7]

With option [7] enabled in section [501], Tamper Recognition

follows the zone bypass definition. This means that the control

panel will not perform any action if a tamper or wire fault occurs on

a bypassed zone. With option [7] disabled, the control panel will

ignore the zone’s bypass definition and will follow the option set in

section 7.4 if a tamper or wire fault occurs on a bypassed zone.

7.5 Keypad Panic Options

SECTIONS [506], [510], [514], [518]: OPTIONS [1] TO [6]

Since the control panel can enable Keypad Panic Options for each

partition, select the section that corresponds to the desired partition

and set options [1] through [6] on/off to obtain the desired options.

Sections [506], [510], [514], and [518] represent partitions 1 to 4

respectively.

Panic 1:

Option [1] ON/OFF= Enabled/Disabled

Option [4] ON = Panic 1 is Audible

Option [4] OFF = Panic 1 is Silent

For LCD keypads: Press and hold keys [1] and [3] simultaneously

on the LCD keypad for 2 seconds to generate a Panic 1 alarm.

For Grafica keypads: Press and hold the key on the Grafica

keypad for 2 seconds to generate a Panic 1 (Medical) alarm.

Panic 2:

Option [2] ON/OFF= Enabled/Disabled

Option [5] ON = Panic 2 is Audible

Option [5] OFF = Panic 2 is Silent

For LCD keypads: Press and hold keys [4] and [6] simultaneously

on the LCD keypad for 2 seconds to generate a Panic 2 alarm.

For Grafica keypads: Press and hold the key on the Grafica

keypad for 2 seconds to generate a Panic 2 (Auxiliary) alarm.

Panic 3:

Option [3] ON/OFF= Enabled/Disabled

Option [6] ON = Panic 3 is Pulsed (Fire)

Option [6] OFF = Panic 3 is Silent

For LCD keypads: Press and hold keys [7] and [9] simultaneously

on the LCD keypad for 2 seconds to generate a Panic 3 alarm.

For Grafica keypads: Press and hold the key on the Grafica

keypad for 2 seconds to generate a Panic 3 (Fire) alarm.

Silent Operation

The control panel emits a single Confirmation Beep and transmits

the appropriate report code (see section 8.2.5 on page 25) to the

monitoring station.

Audible Operation

The alarm output (bell/siren) activates until a user cancels the

alarm with a valid user access code or when the Bell Cut-Off Timer

elapses (see section 7.2).

Fire Operation

Same as audible operation, except that the bell/siren output will be

pulsed as shown in Figure 16 on page 13.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex DGP-641 Manual de instalación Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex DGP-641