Digiplex EVO641R Manual de instalación descargar pdf (Pagina 9)

Digiplex -EVO- - 9 - Programming Guide

Zone Programming

Enter Section [0400], then

enter the number of the

zone you want to program

Enter the zone’s 8-digit

serial and 3-digit input

number (The input number

is not needed for module

with only one input)

Press [0] followed by [Enter]

to clear a zone’s serial

number.

Enter the zone’s parameters

(01) (*2*4***) default

Enter the zone’s report

codes

(00) (00) (00) (00) default

Enter the zone’s label

Press [ENTER] to save and

go to the next zone

Pressing [CLEAR] twice will

exit the zone programming

menus. Press [ENTER]

before pressing clear to

save your modifications.

Zone Definition Partition Zone Option

_____ _____ 1 2 3 4 5 6 7 8

0 - Disabled (default)

1 - Entry Delay 1

2 - Entry Delay 2

3 - Follow

4 - Instant

5 - 24Hr Buzzer

6 - 24Hr Burglary

7 - 24Hr Hold-up

8 - 24Hr Gas

9 - 24Hr Heat

A - 24Hr Water

B - 24Hr Freeze

C - Delayed 24Hr Fire

D - Standard 24Hr Fire

E - Stay Delay 1

F - Stay Delay 2

1 - Assigned to Partition 1

(default)

2 - Assigned to Partition 2

3 - Assigned to Partition 3

4 - Assigned to Partition 4

5 - Assigned to Partition 5

6 - Assigned to Partition 6

7 - Assigned to Partition 7

8 - Assigned to Partition 8

[1] Auto Zone Shutdown Enabled

[2] Bypass Enabled (default on)

[3] Stay Zone

[4] Force Zone (default on)

[5] [6] Zone Alarm Type

off off Steady Alarm

off on Pulsed Alarm

on off Silent Alarm

on on Report Only

[7] Intellizone

[8] Delay before Transmission

Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats:

Key-in desired 2-digit hex values from 00 to FF.

Ademco format:

Use section [4032] to program a set of default Ademco report codes from the

Automatic Report Code Programming on page 50. Then to program the remaining

report codes or to change some of the defaults, enter the individual sections and

key-in the desired 2-digit hex value found in the Contact ID Report Code List on

page 53.

SIA format:

Use section [4032] to program a set of SIA report codes from the Automatic Report

Code Programming on page 50. Codes that have not been set to default can be set

to default manually by entering FF in the appropriate section. To disable the

reporting of an event, enter 00 in the appropriate section

Alarm Report Code

Alarm Restore

Report Code

Tamper Report

Code

Tamper Restore

Report Code

__ / __ __ / __ __ / __ __ / __

In any Zone Programming option, pressing [ACC] will save the data and go

to the next zone on the same option screen. Pressing [TRBL] will save the

data and go to the previous zone on the same option screen.

Input 2

Hardwired

Device B

Control Panel

SN#:020000A2

APR3-ZX8 Module

SN#: 34000041

Input 5

Detector A

SN#: 21000033

OMMUNICATION

ETWORK

Input Terminals

1 2 3 4 5 6 7 8

Detector A:

Hardwired Device A:

Hardwired Device B:

Hardwired Device C:

Zone#

1 =

2 =

3 =

4 =

Section#

[0001]

[0002]

[0003]

[0004]

Serial#

21000033

1A000252

020000A2

34000041

Input#

N/A

002

005

Keypad

SN#: 1A000252

Keypad Zone

Hardwired

Device C

Hardwired

Device A

Input Terminals

1 2 3 4 5 6 7 8

Combus

Section [0400] is accessible only when using EVO641 and EVO641R keypads. Without section [0400], you can only program the

first 96 zones of the system using sections [0001] to [0096] for the zone’s serial number and input, sections [0101] to [0196] for

zone parameters, sections [0201] to [0296] for report codes and sections [0301] to [0396] for zone labels. In addition, with a

EVO48 panel, you can only program the first 48 zones with or without section [0400].

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 67 68

Comentarios a estos manuales

Sin comentarios

Digiplex EVO641R Manual de instalación Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex EVO641R