Digiplex EVO641R Manual de instalación Pagina 56
- Pagina / 68
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Digiplex -EVO- - 56 - Programming Guide
LCD Keypad Programming
The keypad’s serial number can be found on the keypad’s PC board. The keypad’s serial number can also be viewed by pressing and holding the [0] key,
entering the [
INSTALLER CODE] and then entering section [0000] The version of the keypad’s firmware can also be seen in that section.
= Default setting
* Section/option is only available with EVO641 / EVO641R keypads
† Section/option is only available with LCD keypad with built-in reader
‡ Section/option is only available with standard LCD keypad
SECTION [001] : Keypad Partition Assignment
SECTION [002]: Assigning Doors to Partitions †
Option OFF ON Option OFF ON
[1]
Partition 1 N Disabled
Enabled
[1]
Door Assigned to Partition1 N Disabled
Enabled
[2] Partition 2 N Disabled
Enabled
[2]
Door Assigned to Partition 2
Disabled
NEnabled
[3] Partition 3 N Disabled
Enabled
[3]
Door Assigned to Partition 3
Disabled
NEnabled
[4] Partition 4 N Disabled
Enabled
[4]
Door Assigned to Partition 4
Disabled
NEnabled
[5] Partition 5 N Disabled
Enabled
[5]
Door Assigned to Partition 5
Disabled
NEnabled
[6] Partition 6 N Disabled
Enabled
[6]
Door Assigned to Partition 6
Disabled
NEnabled
[7] Partition 7 N Disabled
Enabled
[7]
Door Assigned to Partition 7
Disabled
NEnabled
[8] Partition 8 N Disabled
Enabled
[8]
Door Assigned to Partition 8
Disabled
NEnabled
SECTION [003]: General Options 1 SECTION [004]: General Options 2
Option OFF ON Option OFF ON
[1] Display code entry
Disabled
N Enabled [1] Mute Keypad
Disabled
N Enabled
[2] Display exit delay
Disabled
N Enabled [2] Exit Delay Beep N Disabled
Enabled
[3] Display entry delay
Disabled
N Enabled [3]
Door Left Open Pre-Alarm †
N Disabled
Enabled
[4] Confidential Mode
(not for UL installations)
Disabled
N Enabled [4] Chime on Zone Closure
Disabled
N Enabled
[5] To exit Confidential Mode
Enter code
N
Press Button
[5]
Door Left Open Alarm Feedback †
N Silent
Audible
[6] Future Use N N/A N N/A [6] Door Left Open Alarm Follows †
Alarm
restore
N Beep Timer
[7] Future Use N N/A N N/A [7]
Door Forced Alarm †
N Silent
Audible
[8] Time display option
yy/mm/dd
N dd/mm/yy [8] Door Forced Alarm †
Alarm
restore
N Beep Timer
SECTION [005] : Beep on Trouble
SECTION [006]: PGM and Tamper Options
Option OFF ON Option OFF ON
[1] System & Clock Trouble Beep
Disabled
N Enabled
[1] PGM State‡
N.O.
N N.C.
[2] Communicator Trouble Beep
Disabled
N Enabled
[2] PGM Deactivation Mode‡
Deactiva
tion
Event
N PGM Timer
[3] Module & Combus Trouble Beep
Disabled
N Enabled
[3] PGM Base Time‡
1 second
N 1 minute
[4]
All Zone Trouble Beep
Disabled
N Enabled
[4] PGM Override‡
Disabled
N Enabled
[5] to [6]
Future Use N N/A N N/A [5] Keypad Tamper
Disabled
N Enabled
[7] Time Format
24Hr clock
N 12Hr clock
[6] to [8]
Future Use N N/A N N/A
[8] Audible Feedback on Access
Request*
N Disabled
Enabled
- Hardware Requirements 2
- Hardware Differences 2
- Table of Contents 3
- Things You Should Know 3
- Entering Programming Mode 3
- Serial Number List 4
- Zone Programming 9
- Zone Information 10
- Zone report codes 15
- Zone Labels 17
- Keyswitch Programming 19
- Programmable Outputs 21
- †: See page 27 25
- † 001 to 064 001 to 064 25
- † Not Used Not Used 25
- Input Speeds 28
- Installer Code Programming 28
- User Code Options 29
- Arming Report Codes 30
- Disarming Report Codes 30
- Access Control Sections 31
- Schedule Programming 32
- SECONDARY SCHEDULES 33
- Backup Schedules 34
- Programming Access Levels 34
- Holiday Programming 34
- Keypad Numbering 35
- Remote Control Programming 35
- Control Panel Settings 36
- System Options 36
- Dialer Options 38
- Other Options 38
- Communication Settings 39
- Reporting Formats 40
- VDMP3 Voice Module 41
- Partition Settings 42
- Partition Timers 43
- Partition Options 1 43
- Partition Panic Alarm Options 45
- Partition Bell Squawk Options 45
- Partition One-Touch Options 45
- Partition Special Options 46
- Special Arming Exit Delay 47
- No Movement Schedule 47
- Other Settings and Modes 49
- Software Reset 50
- Installer Function Keys 51
- Automatic Report Code List 51
- System Event 52
- Default SIA Report Code 52
- Contact ID Report Code List 53
- VDMP3 Installation Diagram 55
- Feature Activation (PGMs) 55
- N 12Hr clock 56
- N Disabled 56
- [018]: Beeping Assignment* 57
- Message Programming 58
- Using the Memory Key 59
- Memory Key (PMC-5) 59
- Combus Voltmeter 59
- BLK and Z1 terminals 60
- BLK and Z2 terminals 60
- Single Zone Inputs 61
- ATZ - Double Zone Inputs 61
- Connections 62
- Telephone Line Connections 63
- Built-in RTC 64
- PCB Layout 65
- Warranty 67
- Limitations of Alarm Systems 67
- Trouble Display 68
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Digiplex EVO641R
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales